Front sprocket nut on my GSXR 600 K8 is knackered. It's more of a washer than a nut. Have found this one on ebay to replace: ON EBAY HERE
£16.95
for a nut!!Does anyone know where I can get one at a more reasonable price?
Cheers
Steve
GSXR 600 Front Sprocket
-
STEVIEBOY491
- Scything Through The Field
- Posts: 161
- Joined: Sat Jul 17, 2010 6:43 pm
- D/P/T/M/S: Driver/Passenger
- Full Name: Steve Jackson
- Location: Leicestershire
GSXR 600 Front Sprocket
Hi there,
Front sprocket nut on my GSXR 600 K8 is knackered. It's more of a washer than a nut. Have found this one on ebay to replace: ON EBAY HERE
£16.95 for a nut!!
Does anyone know where I can get one at a more reasonable price?
Cheers
Steve
Front sprocket nut on my GSXR 600 K8 is knackered. It's more of a washer than a nut. Have found this one on ebay to replace: ON EBAY HERE
£16.95
for a nut!!Does anyone know where I can get one at a more reasonable price?
Cheers
Steve
-
G JONES
- Lapping the Tail Enders
- Posts: 383
- Joined: Wed Jun 14, 2006 8:28 pm
- D/P/T/M/S: D
- Full Name: Gordon Jones
- Location: Shropshire
- Contact:
Re: GSXR 600 Front Sprocket
Suzuki Part # 09159-20004-000 - if that's the one - I can get one about £12 + post - I do keep a Yam 20mm sprocket nut - half that price if it's the same thread - can you check the pitch of the thread ?STEVIEBOY491 wrote:Hi there,
Front sprocket nut on my GSXR 600 K8 is knackered. It's more of a washer than a nut. Have found this one on ebay to replace: ON EBAY HERE
£16.95
Does anyone know where I can get one at a more reasonable price?
Cheers
Steve
2 strokes are the future...
TZ Parts List
http://tz350.co.uk
Had to laugh at this I heard somewhere... "You can't polish a Turd"
TZ Parts List
http://tz350.co.uk
Had to laugh at this I heard somewhere... "You can't polish a Turd"
-
STEVIEBOY491
- Scything Through The Field
- Posts: 161
- Joined: Sat Jul 17, 2010 6:43 pm
- D/P/T/M/S: Driver/Passenger
- Full Name: Steve Jackson
- Location: Leicestershire
Re: GSXR 600 Front Sprocket
Gordon,
Many thanks for the reply. Don't want to put you out, but many thanks for the offer of help
Cheers
Steve
Many thanks for the reply. Don't want to put you out, but many thanks for the offer of help
Cheers
Steve
-
G JONES
- Lapping the Tail Enders
- Posts: 383
- Joined: Wed Jun 14, 2006 8:28 pm
- D/P/T/M/S: D
- Full Name: Gordon Jones
- Location: Shropshire
- Contact:
Re: GSXR 600 Front Sprocket
A lot of the manufacturer parts prices are inflated on Ebay - must remember though - it will cost the seller approx 13% in ebay & paypal costs - so that price wasn't too far out - looks like that nut is not just an ordinary 20mm nut either...the Yam one is just a recessed nut - tightens up against a splined tab washer...STEVIEBOY491 wrote:Gordon,
Many thanks for the reply. Don't want to put you out, but many thanks for the offer of help
Cheers
Steve
Give me a shout - if I can help I will...
2 strokes are the future...
TZ Parts List
http://tz350.co.uk
Had to laugh at this I heard somewhere... "You can't polish a Turd"
TZ Parts List
http://tz350.co.uk
Had to laugh at this I heard somewhere... "You can't polish a Turd"
-
rugbyfan
- Scything Through The Field
- Posts: 100
- Joined: Tue Jun 09, 2009 10:50 am
- D/P/T/M/S: Marshal
- Full Name: Sam Talbot
- Location: Sitting on the hedge
Re: GSXR 600 Front Sprocket
It's a bit more than a washer, torqued to 83 lbft.
-
STEVIEBOY491
- Scything Through The Field
- Posts: 161
- Joined: Sat Jul 17, 2010 6:43 pm
- D/P/T/M/S: Driver/Passenger
- Full Name: Steve Jackson
- Location: Leicestershire
Re: GSXR 600 Front Sprocket
Sam,
It was little more than a washer as it had no threads left! The speed sensor bolt was holding it all together. Has now been changed.
Cheers
Steve
It was little more than a washer as it had no threads left! The speed sensor bolt was holding it all together. Has now been changed.
Cheers
Steve